Products Essential
Two '/*" x Γ 18-gauge sterling silver sheet silver Two 7/«" sterling silver bar components Two five.three mm x 3.2 mm sixteen-gauge sterling silver oval bounce rings Two sterling silver ear wires
Applications Desired
Ruler
Marker
Jeweler's noticed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
Great grit sanding pad Awl
Tricky, flat floor /Îί’ drill bit
Handheld rotary tool, flex shaft, or drill push Liver of sulfur or oxidizing Resolution Fantastic steel wool Sprucing cloth
Two pairs of chain nose pliers
1.Utilize the ruler to measure and mark two
rectangle pieces of eighteen-gauge sterling sheet silver.
2.Utilizing a jeweler's saw or tin snips, cut the eighteen-gauge sterling sheet silver into two Vi" x Γ rectangles (if you may be making the bracelet and pendant initiatives, you may want to Slice every one of the rectangle silver parts essential for one other initiatives and texture them all at one particular time).
three.Area the two W x Γ sterling silver rectangle items on to the sticky side of a bit of masking tape. This can help you to carry the silver rectangles in place while you're texturing them, and can even aid to keep the fingertips at a secure length to prevent hitting them Along with the hammer.
four.Place the piece of masking tape With all the silver rectangles sticky facet down on to a concrete block or landscape paver.
five.Which has a hammer, Carefully strike the tape-covered silver rectangles using a company strike, but Will not hit also challenging. You can achieve the specified texture more easily with numerous soft strikes rather than a few hard strikes. Carry the tape routinely and Look at the development in the texturing, making sure that the entire area on the silver rectangles is getting a uniform texture. The area will glance much like sandpaper In case you are using a concrete block. Any time you accomplish the specified texture, take away the silver rectangles in the masking tape.
six.the silver rectangles may have a slight curve to them, and the sides will probably be misshapen and sharp Once you texture them. You'll be able to go away the silver rectangles curved or, to flatten them, spot the silver rectangles on a tough, flat area and use a rawhide mallet to flatten them. If you don't Have got a rawhide mallet, you'll be able to put the silver rectangles on a hard, flat surface area, deal with the pieces by using a thick bit of scrap leather-based, and use a hammer to gently tap the leather protected silver rectangles to flatten them.
seven.You must utilize a file to get rid of any rough or sharp edges. Make use of a high-quality grit sanding pad to go over the area where you have submitted to sleek the sides and take away any file marks.
eight.Evaluate from just one close of each and every buy men's rings textured silver rectangle and place a mark in the center of each piece. This is when the holes are going to be drilled to connect the soar ring and bar parts.
9.Put on the security Eyeglasses. Area the textured silver rectangles onto a hard, flat surface. Put The purpose on the awl within the mark that you simply produced '/t" within the conclusion on the rectangle men's gold & silver rings pieces and utilize a hammer to firmly strike after on the top of your awl for making a pilot hole for drilling the holes into your silver rectangles.
10.Employing a drill bit, drill holes into Each individual on the silver rectangles having a handheld rotary Resource, flex shaft, or men's rings personalized and engraved drill press. Remember to have on security Eyeglasses.
11.Make use of the file or sanding pad to get rid of any burs or tough edges remaining from drilling holes in to the silver rectangles.
twelve.Utilize liver of sulfur or oxidizing Answer to your textured silver rectangles, bar components. and leap rings. It is vital to abide by any safety recommendations the maker implies when dealing with any chemicals.
13.Soon after implementing the oxidizing solution, use good steel wool to remove the darkened places men's college ring about the elevated floor with the silver rectangles, leaving a lot of the textured spots dim. Rub the great metal wool over the bounce rings and bar factors to eliminate some although not every one of the darkened regions. Rinse with drinking water, dry, and rub with polishing fabric.
fourteen.With two pair of chain nose pliers pointing up, hold the bounce ring While using the opening at the highest. Roll one particular of the wrists far from you and your other wrist towards you, opening the soar ring only just as much as needed. To close the jump ring, maintain it precisely the same way and roll your wrists in the opposite way (imagine holding a bit of paper and tearing it). Never ever pull the jump ring finishes out as this may weaken the steel, and it will be tough to shut the leap ring.
fifteen.Incorporate the bar component and textured silver rectangle on the bounce ring. Near men's rings the soar ring.
sixteen.Gently open up the loop at The underside from the ear wire, insert the other conclude of your bar component. and afterwards shut the ear wire loop.
17.Repeat these measures for the next earring.